Description
Using logical or numerical inputs from its 16 analogue inputs or from any of 3 CAN buses the PDUX3 is calibrated using a clear graphical interface with full logic simulation ability and live monitoring.
The PDUX3 is able to operate in a low power standby state, drawing <2mA, with configurable activation based on physical or CAN input. Additionally, the PDUX3 may be paired with a Life Racing ECU to expand input and output functionality through the ‘slave-link’ feature.
Multiple variants of the PDUX3 are available; 12V/350A or 12V/200A – Please make your selection whilst placing your order in the options above.
Life Racing PDUX3 Power Distributor Unit Specification:
Features
- Schematic based calibration including logic simulation tool
- Numerical arithmetic including handling of analogue inputs
- Fully custom CAN across 3 buses including mux frames and retransmission (gateway), configured with the help of a graphical display and import/export tool
- Low power state woken on physical input, CAN activity, or specific CAN frame
- Optional I/O slaving to an LR ECU
Outputs
- 34 main Power Outputs
- 10 multifunction high side, low side, high side PWM (fixed 20kHz) outputs (40A continuous, soft-start inrush limiting 40A, hard-start inrush 60A)
- 10 high side outputs (40A continuous, hard-start inrush 60A)
- 14 high side outputs (15A continuous, hard-start inrush 17.5A)
- Output linking (‘teaming’) to support very high current devices
- 4 additional low side outputs (125Hz PWM)
- All outputs short circuit and thermally protected with multi-stage in-rush control
- All outputs additionally protected by physical fuses as required by worldwide regulations
- Combined diagnostic output with reset input
- 128 scaleable CAN (‘soft’) outputs
- Custom datastream (CAN) – i.e. customisable channel current, channel state and device information
Inputs
- 16 physical switch / analogue sensor inputs including software selectable 3k ohmpull-up resistors and 4x inputs capable of programmable “wake up” functionality
- Analogue inputs may be transformed into engineering units for use in schematic
- Dedicated wake pin
- 128 CAN ‘soft’ inputs with configurable scaling, validation and debounce time
Interfaces
- 2x 100Mbit/s full duplex Ethernet (can be used as Ethernet switch)
- 3x CAN 2.0B – fully flexible
- Option for galvanically isolated CAN bus (custom projects only)
- RS232C serial interface (custom projects only)
- LIN Bus (custom projects only)
Power Supply
- 6V to 20V input voltage (12V option) or 6V to 30V input voltage (24V option)
- Dedicated logic power input
- Regulated 5V sensor supply output with full circuit protection
Sleep State
- Low power standby state with configurable wake options:
- Wake by voltage signal (1.6mA)
- Wake by any CAN activity (CAN1 only) (2mA)
- Wake by specific CAN frame (two frames required, CAN1 only) (2mA)
- Wake by CAN specific CAN frame with low latency (one frame required, CAN1 only) (10mA)
ECU Slaving
- Allows a Life Racing ECU to “claim” unused pins across a dedicated CAN bus utilising the following PDU I/O:
- Outputs 1..10 with additional functionality including H-Bridge pairing and configurable PWM frequencies
- Low Outputs 11..14 with configurable PWM frequencies
- All 16 inputs, including 8 frequency capable (4 optionally bipolar), and all with software selectable 3k ohm pull-up resistors
Physical
- 2 Leavyseal connectors with a total of 113 pins
- Amphenol SurLok Power Stud
- Machined Aluminium enclosure
- 210x130x57mm (including connectors)
- 1090 grams
- Operating Temperature -40C to +85C
Warranty and Servicing
- This equipment comes with a 1 year warranty against manufacturing defects and failures however misuse or damage will not be covered under warranty
Here at Northampton Motorsport, we also offer a full wiring and fitting service as well as engine calibration on our in house Superflow AD30 2 wheel drive chassis dyno. For more information, please contact us and a member of our team would be happy to assist with your enquiry:
Estimated dispatch time within 10 working days.
Picture for illustration purposes only. Actual parts may differ slightly in appearance.